How To increase RTX 3060 Ti LHR Mining: Overclocking| Best Settings| ETH & MSI

Best overclocking settings for GeForce RTX 3060 Ti LHR

Ethereum mining performance and benchmarks

To test the mining performance of our card, we tested five different miners: NBminer 39.5, GMiner 2.70, lolMiner 1.33, T-Rex 0.24, and miniZ v1.8y4rc2 miner. All tests were run with the overclocking settings applied and on a Windows 10 PC with NVIDIA 471.68 graphics drivers. Fan speed, GPU core temperature, video memory temperature, and total board power consumption were recorded using HWiNFO64 v7.14. Below you can see the results of our tests.

RTX 3060 Ti LHR (OC)Hashrate (Average)GPU Temperature (Average)Fan speed (average)Total power consumptionEff. / W
NBMiner 39.5
(LHR 68.4)
40.10 MH / s42 ° C80%102 watts393.1 kg / J
GMiner 2.70
(LHR 70)
40.30 MH / s41 ° C80%102 watts395.1 kg / J
T-Rex 0.24
(—lhr-tune-71)
42.00 MH / s44 ° C80%129 watts325.6 kH / J
lolMiner 1.33
(—lhr-tune 17)
42.50 MH / s44 ° C80%122 watts348.3 kg / J
MiniZ 1.8y4rc2
(—mode = 80)
42.60 MH / s45 ° C80%129 watts330.2 kH / J
Ethereum mining performance and benchmarks

Almost all miners work roughly the same with the GeForce RTX 3060 Ti LHR, however there are some minor differences worth talking about. If you take a close look at our table above, you can see that NBMiner 39.5 performs the worst (at least when it comes to raw mining hashrate), while the miniZ miner performs best. It is also worth noting that there is practically no difference in performance between NBMiner and GMiner, so it is safe to say that these two miners perform almost the same.

Read This Now:   Intel Core i7-11700K Processor: Review (Special)| Overclocking| Benchmark | Specs

The situation is much more complicated when it comes to efficiency. This is where both NBMiner and GMiner take the crown as with these two RTX 3060 Ti miners the LHR only draws about 102W of power, while with the miniZ and T-Rex miner it draws almost 130W of power. The increased power consumption also causes increased heat dissipation, so it should come as no surprise that the RTX 3060 Ti heats up a bit with the miniZ and T-Rex miners. Below you can see a performance efficiency chart that gives a much better idea of ​​the performance differences between the tested miners.

MinerHashrate (MH / s)Eff. / W (kH / J)
NBMiner 39.540.1393.1
GMiner 2.7040.3395.1
Tyrannosaurus 0.2442325.6
lolMiner 1.3342.5348.3
MiniZ 1.8y4rc242.6330.2
Hashrate (MH / s): Ethereum mining performance and benchmarks RTX 3060 Ti LHR (OC)

As you can see, GMiner is the best miner if you have an RTX 3060 Ti LHR. This miner can provide maximum efficiency and it has a developer fee of 0.65%, which is slightly less compared to NBMiner’s 1% fee. Of course, if sheer mining performance is all you care about, consider switching to lolMiner. It is not only more efficient than the T-Rex miner, but also has a lower developer commission – just 0.7%. Compared to GMiner, with lolMiner you can expect higher power consumption and slightly worse mining efficiency, but on average your card will hash at about 42.5 MH / s.

Read This Now:   How to increase Sapphire RX 570 Pulse ITX Mining: Overclock| Hashrate| MSI (BIOS)

MiniZ is also a pretty good miner when it comes to sheer performance, however the time you spend fiddling with it doesn’t really justify its high hash rate. You see, miniZ comes with tons of options that will leave you spending hours until you find the best setting that suits your needs. In general, miniZ is quite unstable and causes a lot of system crashes, so be prepared if you decide to choose this miner. Of course, if you like to constantly optimize and test your GPU’s mining performance, then miniZ is the best option, but if you just want to mine as efficiently as possible, then GMiner seems like a much better

Overall, none of the miners we tested showed impressive performance gains, however, all of them were able to partially unleash the mining potential of the RTX 3060 Ti and increase its hashrate to 33%. In truth, this performance boost isn’t all that bad, but it still leaves a lot to be desired, especially since the non-LHR GeForce RTX 3060 Ti can hit 60 MH / s at 130W without any tweaks.

Read This Now:   How to Overclock AMD Radeon R9 270X Gaming: Benchmarks + fresh drivers + Windows (10,8, 7)
Best overclocking settings for  RTX 3060 Ti LHR
Best overclocking settings for RTX 3060 Ti LHR

You also have to be very careful whether your RTX 3060 Ti LHR is equipped with Samsung or Hynix memory modules. Samsung memory cards tend to perform slightly better, which means they can handle around 45 MH / s, while Hynix memory cards can handle 37 to 42 MH / s.

Despite its limited mining performance, the GeForce RTX 3060 Ti LHR seems like a card with a lot of potential and we hope that cryptocurrency miners will discover new solutions that will allow them to fully unlock LHR cards. We hope you enjoyed this guide and found this information helpful. If you have any thoughts that you would like to share with us, feel free to leave comments below. Happy mining!


Notice: ob_end_flush(): failed to send buffer of zlib output compression (1) in /home/gamefeve/bitcoinminershashrate.com/wp-includes/functions.php on line 5373

Notice: ob_end_flush(): failed to send buffer of zlib output compression (1) in /home/gamefeve/bitcoinminershashrate.com/wp-includes/functions.php on line 5373