How to Install the Ultimaker Cura Cutter on Linux – Easy Steps

Ultimaker Cura is one of the best 3D printer cutter apps out there. It has dozens of great features like material estimation, support for a wide variety of printers (even those not made by Ultimaker), and much more. This guide will show you how to install Ultimaker Cura on Linux.

Ubuntu installation instructions

To set up the Cura Slicer on Ubuntu, you will first need to enable the Ubuntu Universe software repository. This software repository can be enabled with a simple terminal command.

Open a terminal window on the Linux desktop by pressing Ctrl + Alt + T on the keyboard. Alternatively, start a terminal by searching for “Terminal” in the application menu. Once it’s open, use the add-apt-repository command below.

sudo add-apt-repository universe

Following the above command, you need to update the Ubuntu software sources. To update, run the apt upgrade command.

sudo apt update

Finally, you will be able to install the Cura slicer application using the apt install command.

sudo apt install cura

When you type the above command, Ubuntu will ask for your password. Using the keyboard, enter your password. Then press the Get into wrench. When you have entered your password, Ubuntu will ask if you want to install Cura. press the Y key to confirm.

Debian Installation Instructions

The Cura slicer application is available for Debian Linux users. Start by opening a terminal window on the Linux desktop to get it working on your Debian system. You can start a terminal by pressing Ctrl + Alt + T on the keyboard. Or search for “Terminal” in the application menu.

When the terminal window is open, use the apt-get install command to configure the “cure” package on your computer. Keep in mind; you must be using Debian 10, 11, or Sid for this command to work.

sudo apt-get install cura

Once you type the above command, Debian will ask you for a password. Using the keyboard, enter the password for your user account. Then press the Get into key to confirm.

After entering a password, Debian will ask if you want to install the Cura package on your computer. press the Y at the keyboard to confirm your choice and install the Cura cutter on Debian.

Arch Linux Installation Instructions

Ultimaker Cura is in the “Community” software repository for all Arch Linux users. To make it work on your system, make sure you have this repository enabled in your Pacman settings.

To start the installation, open a terminal window on the desktop. You can open a terminal window by pressing Ctrl + Alt + T on the keyboard. Or search for “Terminal” in the application menu and run it that way.

With the terminal window open, use the pacman -S command to install the “cure” package on your computer.

sudo pacman -S cura

Arch Linux will ask for your password when you type the above command. Using the keyboard, enter your password for your username. Then press the Get into key to confirm.

After confirming your password, Arch Linux will ask you if you want to install the software on your computer. press the Y to confirm your choice. When the Y the key is pressed, Arch Linux will install Cura.

Fedora Installation Instructions

The Cura slicer application is available to Fedora Linux users from all major software repositories. Open a terminal window on the Linux desktop to make it work on your system.

You can open a terminal window on the desktop by pressing Ctrl + Alt + T on the keyboard. Or search for “Terminal” in the application menu and run it that way. With the terminal window open, use the instalar dnf command to configure the “cure” package on your computer.

sudo dnf install cura

Once you type the above command, Fedora will ask for your password. Using the keyboard, enter the password for your user account. Then press the Get into key to confirm.

When you have entered your password, Fedora Linux will ask you to press the Y to confirm that you want to install the Cura application on your computer.

OpenSUSE Installation Instructions

OpenSUSE Linux has the Cura application available to Leap users, as well as Tumbleweed, through the official software repositories. To get it working on your computer, start by opening a terminal window.

If you want to open a terminal window on the desktop, press Ctrl + Alt + T on the keyboard. Or search for “Terminal” in the application menu and open it. Once the program is open, use the zypper installation command below to install the «cure» application.

sudo zypper install cura

When typing the above command in the terminal, OpenSUSE Linux will ask you to enter your password. Using the keyboard, enter your password. Then press the Get into wrench.

Once the Get into press the key, OpenSUSE will ask you to confirm that you want to install Cura by pressing the key Y wrench. Do it to install Cura.